Hcxdumptool - Small Tool To Capture Packets From Wlan Devices - Hacking Land

Small tool to capture packets from wlan devices. After capturing, upload the "uncleaned" cap here (https://wpa-sec.stanev.org/?submit) to see if your ap or the client is vulnerable by using common wordlists. Convert the cap to hccapx and/or to WPA-PMKID-PBKDF2 hashline (16800) with hcxpcaptool (hcxtools) and check if wlan-key or plainmasterkey was transmitted unencrypted.

Brief description

Stand-alone binary - designed to run on Raspberry Pi's with installed Arch Linux. It should work on other Linux systems (notebooks, desktops) and distributions, too.

Detailed description

Tool	Description
hcxdumptool	Tool to run several tests to determine if access points or clients are vulnerable
pioff	Turns Raspberry Pi off via GPIO switch

Compile
Simply run:

make
 make install (as super user)

or (with GPIO support - hardware mods required)

make GPIOSUPPORT=on
 make GPIOSUPPORT=on install (as super user)

Requirements

Operatingsystem: Arch Linux (strict), Kernel >= 4.14 (strict). It should work on other Linux systems (notebooks, desktops) and distributions, too (no support for other distributions). Don't use Kernel 4.4 (rt2x00 driver regression)
libpthread and pthread-dev installed
Raspberry Pi: additionally libwiringpi and wiringpi dev installed (Raspberry Pi GPIO support)
Chipset must be able to run in monitor mode (strict by: ip and iw). Recommended: RALINK chipset (good receiver sensitivity), rt2x00 driver (stable and fast)
Raspberry Pi A, B, A+, B+ (Recommended: A+ = very low power consumption or B+), but notebooks and desktops could work, too.
GPIO hardware mod recommended

Supported adapters (strict)

USB ID 148f:7601 Ralink Technology, Corp. MT7601U Wireless Adapter
USB ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless Adapter
USB ID 148f:5370 Ralink Technology, Corp. RT5370 Wireless Adapter
USB ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter
USB ID 0bda:8189 Realtek Semiconductor Corp. RTL8187B Wireless 802.11g 54Mbps Network Adapter

Useful scripts

Script	Description
bash_profile	Autostart for Raspberry Pi (copy to /root/.bash_profile)
pireadcard	Back up a Pi SD card
piwritecard	Restore a Pi SD card
makemonnb	Example script to activate monitor mode
killmonnb	Example script to deactivate monitor mode

Hardware mod - see docs gpiowait.odg (hcxdumptool)
LED flashes 5 times if hcxdumptool successfully started
LED flashes every 5 seconds if everything is fine
Press push button at least > 5 seconds until LED turns on (LED turns on if hcxdumptool terminates)
Green ACT LED flashes 10 times
Raspberry Pi turned off and can be disconnected from power supply
Do not use hcxdumptool and hcxpioff together!

Hardware mod - see docs gpiowait.odg (hcxpioff)
LED flashes every 10 seconds 2 times if hcxpioff successfully started
Press push button at least > 10 seconds until LED turns on (hcxpioff will shut down Raspberry Pi safely)
Green ACT LED flashes 10 times
Raspberry Pi turned off and can be disconnected from power supply
Do not use hcxdumptool or hcxpioff together!

Warning
You must use hcxdumptool only on networks you have permission to do this, because

hcxdumptool is able to prevent complete wlan traffic
hcxdumptool is able to capture PMKIDs from access points (only one single PMKID from an access point required)
hcxdumptool is able to capture handshakes from not connected clients (only one single M2 from the client is required)
hcxdumptool is able to capture handshakes from 5GHz clients on 2.4GHz (only one single M2 from the client is required)
hcxdumptool is able to capture extended EAPOL (RADIUS, GSM-SIM, WPS)
hcxdumptool is able to capture passwords from the wlan traffic
hcxdumptool is able to capture plainmasterkeys from the wlan traffic
hcxdumptool is able to capture usernames and identities from the wlan traffic