UDPX - Fast A Nd Lightweight, UDPX Is A Single-Packet UDP Scanner Written In Go That Supports The Discovery Of Over 45 Services With The Ability To Add Custom Ones - Hacking Land

Fast and lightweight, UDPX is a single-packet UDP scanner written in Go that supports the discovery of over 45 services with the ability to add custom ones. It is easy to use and portable, and can be run on Linux, Mac OS, and Windows. Unlike internet-wide scanners like zgrab2 and zmap, UDPX is designed for portability and ease of use.

It is fast. It can scan whole /16 network in ~20 seconds for a single service.
You don't need to instal libpcap or any other dependencies.
Can run on Linux, Mac Os, Windows. Or your Nethunter if you built it for Arm.
Customizable. You can add your probes and test for even more protocols.
Stores results in JSONL format.
Scans also domain names.

How it works

Scanning UDP ports is very different than scanning TCP - you may, or may not get any result back from probing an UDP port as UDP is a connectionless protocol. UDPX implements a single-packet based approach. A protocol-specific packet is sent to the defined service (port) and waits for a response. The limit is set to 500 ms by default and can be changed by -w flag. If the service sends a packet back within this time, it is certain that it is indeed listening on that port and is reported as open.

A typical technique is to send 0 byte UDP packets to each port on the target machine. If we receive an "ICMP Port Unreachable" message, then the port is closed. If an UDP response is received to the probe (unusual), the port is open. If we get no response at all, the state is open or filtered, meaning that the port is either open or packet filters are blocking the communication. This method is not implemented as there is no added value (UDPX tests only for specific protocols).

Usage

Concurrency: By default, concurrency is set to 32 connections only (so you don't crash anything). If you have a lot of hosts to scan, you can set it to 128 or 256 connections. Based on your hardware, connection stability, and ulimit (on *nix), you can run 512 or more concurrent connections, but this is not recommended.

To scan a single IP:

udpx -t 1.1.1.1

To scan a CIDR with maximum of 128 connections and timeout of 1000 ms:

udpx -t 1.2.3.4/24 -c 128 -w 1000

To scan targets from file with maximum of 128 connections for only specific service:

udpx -tf targets.txt -c 128 -s ipmi

Target can be:

IP address
CIDR
Domain

IPv6 is supported.

If you want to store the results, use flag -o [filename]. Output is in JSONL format, as can be seen bellow:

{"address":"45.33.32.156","hostname":"scanme.nmap.org","port":123,"service":"ntp","response_data":"JAME6QAAAEoAAA56LU9vp+d2ZPwOYIyDxU8jS3GxUvM="}

Options

        __  ______  ____ _  __       / / / / __ \/ __ \ |/ /      / / / / / / / /_/ /   /     / /_/ / /_/ / ____/   |     \____/_____/_/   /_/|_|         v1.0.2-beta, by @nullt3rUsage of ./udpx-linux-amd64:  -c int    	Maximum number of concurrent connections (default 32)  -nr    	Do not randomize addresses  -o string    	Output file to write results  -s string    	Scan only for a specific service, one of: ard, bacnet, bacnet_rpm, chargen, citrix, coap, db, db, digi1, digi2, digi3, dns, ipmi, ldap, mdns, memcache, mssql, nat_port_mapping, natpmp, netbios, netis, ntp, ntp_monlist, openvpn, pca_nq, pca_st, pcanywhere, portmap, qotd, rdp, ripv, sentinel, sip, snmp1, snmp2, snmp3, ssdp, tftp, ubiquiti, ubiquiti_discovery_v1, ubiquiti_discovery_v2, upnp, valve, wdbrpc, wsd, wsd_malformed, xdmcp, kerberos, ike  -sp    	Show received packets (only first 32 bytes)  -t string       	IP/CIDR to scan  -tf string    	File containing IPs/CIDRs to scan  -w int    	Maximum time to wait for a response (socket timeout) in ms (default 500)

Building

You can grab prebuilt binaries in the release section. If you want to build UDPX from source, follow these steps:

From git:

git clone https://github.com/nullt3r/udpxcd udpxgo build ./cmd/udpx

You can find the binary in the current directory.

Or via go:

go install -v github.com/nullt3r/udpx/cmd/[email protected]

After that, you can find the binary in $HOME/go/bin/udpx. If you want, move binary to /usr/local/bin/ so you can call it directly.

Supported services

The UDPX supports more then 45 services. The most interesting are:

ipmi
snmp
ike
tftp
openvpn
kerberos
ldap

The complete list of supported services:

ard
bacnet
bacnet_rpm
chargen
citrix
coap
db
db
digi1
digi2
digi3
dns
ipmi
ldap
mdns
memcache
mssql
nat_port_mapping
natpmp
netbios
netis
ntp
ntp_monlist
openvpn
pca_nq
pca_st
pcanywhere
portmap
qotd
rdp
ripv
sentinel
sip
snmp1
snmp2
snmp3
ssdp
tftp
ubiquiti
ubiquiti_discovery_v1
ubiquiti_discovery_v2
upnp
valve
wdbrpc
wsd
wsd_malformed
xdmcp
kerberos
ike

How to add your own probe?

Please send a feature request with protocol name and port and I will make it happen. Or add it on your own, the file pkg/probes/probes.go contains all available payloads. Specify the protocol name, port and packet data (hex-encoded).

{        Name: "ike",        Payloads: []string{"5b5e64c03e99b51100000000000000000110020000000000000001500000013400000001000000010000012801010008030000240101"},        Port: []int{500, 4500},},

Credits

Disclaimer

I am not responsible for any damages. You are responsible for your own actions. Scanning or attacking targets without prior mutual consent can be illegal.